+ Reply to Thread
Results 1 to 8 of 8

Thread: Intermittent starting.

  1. #1
    Join Date
    May 2014
    Location
    State College
    Posts
    82

    Default Intermittent starting.

    On the very EDGE of being able to take the damned D1 to inspection we hit this weird problem when it won't always start. Starts on the first pull sometimes, in fact, just as we put a new battery in it. 10 minutes later, nada, all yesterday afternoon, nada. This evening nada. Offspring tries, worked first time, second and third time. I come home, nothing.

    The non NAS spec versions of the later D1 (1997) didn't have the same immobiliser as the faulty UK ones - so what gives ? Any ideas ? Its booked in for inspection on Wednesday !!!

    Thanks for any tips.
    Steve

  2. #2
    Join Date
    Jan 2007
    Location
    Frenchtown, NJ
    Posts
    547

    Default

    When you changed the ignition key switch, did you reuse the electrical switch from the old (original) key switch? Sound to me like that could be the fault.
    Tom Proctor
    1965 exMod 109
    1995 RRC LWB w/EAS

  3. #3
    Join Date
    Jun 2005
    Location
    Ringwood, NJ
    Posts
    21,130

    Default

    I had a bad starter relay at one point that would give intermittent issues like that. To rule out the electrical system from the starter itself, can you try crossing the terminals on the starter next time you have the issue? Without a heat shield on the starter, access is really easy. If you have a heat shield still then it is hard to get in there. I found an adjustable wrench opened to the match the distance between the two terminals was the easiest way to jump it.
    '89 Range Rover
    '95 D90

  4. #4
    Join Date
    May 2014
    Location
    State College
    Posts
    82

    Default

    Its CRANKING fine, just not running. Except yesterday it was starting like a thoroughbred.
    I HATE intermittent faults.

  5. #5
    Join Date
    May 2014
    Location
    State College
    Posts
    82

    Default

    Quote Originally Posted by Tom109 View Post
    When you changed the ignition key switch, did you reuse the electrical switch from the old (original) key switch? Sound to me like that could be the fault.
    No, we used the new switch too.

  6. #6
    Join Date
    Jan 2007
    Location
    Frenchtown, NJ
    Posts
    547

    Default

    Quote Originally Posted by Steve Taylor View Post
    Its CRANKING fine, just not running.
    So, does "running" = "starting"? In example, it cranks but just won't start (run)?
    Tom Proctor
    1965 exMod 109
    1995 RRC LWB w/EAS

  7. #7
    Join Date
    May 2014
    Location
    State College
    Posts
    82

    Default

    Quote Originally Posted by Tom109 View Post
    So, does "running" = "starting"? In example, it cranks but just won't start (run)?
    running=starting. Its always cranked, but not always starting. Except for the last two days its been OK

  8. #8
    Join Date
    Jan 2007
    Location
    Frenchtown, NJ
    Posts
    547

    Default

    Steve,

    With a GEMS engine, I have only experienced stalling and difficult starts related to the IACV. Once replaced and base idler reset, the problem was sorted. Sorry I can't be much more help than check for Air/Fuel/Spark.

    With the 14cux system I've had to dig a LOT deeper!
    Tom Proctor
    1965 exMod 109
    1995 RRC LWB w/EAS

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts